oanor
Sign up free
Marketplace Pricing Features Sign in

API · /snowload-api

Snow Load API

healthy 4,309 Subscribers

Roof snow-load maths as an API, computed locally and deterministically using the ASCE 7 method. The roof endpoint turns a ground snow load into the design roof snow load: the flat-roof load is pf = 0.7 · Ce · Ct · Is · pg, using the exposure, thermal and importance factors, and the sloped-roof load is ps = Cs · pf, where the slope factor Cs follows the warm-roof all-surfaces curve (1.0 up to 30°, falling linearly to 0 at 70°) or a value you supply. It reports every load in kilopascals, pascals, pounds per square foot and kilograms per square metre, and — if you give a roof area — the total load in kilonewtons, kilograms, tonnes and pounds. The depth endpoint converts a measured snow depth and a density (given directly or by snow type, from fresh ~100 to ice ~917 kg/m³) into a load. The convert endpoint converts a snow load between kPa, psf, kg/m², Pa and psi. Depths accept millimetres, centimetres, metres, inches or feet. Everything is computed locally and deterministically, so it is instant and private. An engineering aid, not a code-stamped design — always confirm against the governing local code with a qualified engineer. Ideal for structural and roofing tools, building-code and permitting apps, solar-install and carport planners, and winter-risk calculators. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is roof snow-load engineering; for roof pitch and area geometry use a roofing API and for beam reactions use a beam API.

#snow-load #structural #roofing #asce7 #engineering #developer-tools
api.oanor.com/snowload-api
Get an API key Try in playground → Contact provider

Machine-readable spec so AI agents can integrate this API.

/api/snowload-api/openapi.json
/api/snowload-api/llms.txt

Discovery: GET /api/index.json lists every API.

API health

healthy
Uptime
100.00%
Server probes · 24h
Avg latency
84 ms
Server probes · 24h
Subscribers
4,309
active
Total calls
40
last 7 days
status Full status page → · 24 probes/24h

Pricing

Pick a tier — billed monthly, cancel anytime.

Free

Free

  • 13,535 calls / month
  • 2 requests / second
  • Hard cap (429 above quota, no overage)
  • 13,535 calls/month
  • 2 req/sec
  • Roof + depth + convert
  • No credit card
Sign in to subscribe

Starter

€15.05 /month

  • 23,250 calls / month
  • 8 requests / second
  • Hard cap (429 above quota, no overage)
  • 23.25k calls/month
  • 8 req/sec
  • ASCE 7 factors, multi-unit
  • Email support
Sign in to subscribe

Pro

€35.05 /month

  • 282,500 calls / month
  • 20 requests / second
  • Hard cap (429 above quota, no overage)
  • 282.5k calls/month
  • 20 req/sec
  • Structural / roofing pipelines
  • Priority support
Sign in to subscribe

Mega

€73.05 /month

  • 1,455,000 calls / month
  • 50 requests / second
  • Hard cap (429 above quota, no overage)
  • 1.455M calls/month
  • 50 req/sec
  • Platform scale
  • Dedicated SLA
Sign in to subscribe

Built by

P
PremiumApi

Related APIs

Other APIs with overlapping tags.

Rebar Calculator API

Reinforcement-steel (rebar) maths as an API, computed locally and deterministically. The area endpoint computes the cross-sectional area of a reinforcing bar, a = π/4·d², its mass per metre (a·7850/1e6, steel ρ = 7850 kg/m³), the total area and mass for a number of bars, and — given a required steel area — the number of bars needed and the area provided. The spacing endpoint lays out bars across a section: from the width, the cover, the bar diameter and either a centre-to-centre spacing or a bar count it returns the other, n = floor((width − 2·cover − d)/spacing) + 1, the total steel area and the area per metre of width. The ratio endpoint computes the reinforcement ratio ρ = As/(b·d) of a section from the steel area (or the bars) and the section width and effective depth, as a fraction and a percentage, the single number that governs whether a beam is under- or over-reinforced. Everything is computed locally and deterministically, so it is instant and private. Ideal for structural and site-engineering tools, reinforced-concrete detailing, bar-bending schedules and steel take-off, and civil-engineering education. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is rebar geometry and quantities; for concrete mix proportions use a concrete API.

api.oanor.com/rebar-api

Wind Load API

Structural wind-load maths as an API, computed locally and deterministically. The pressure endpoint computes the velocity (dynamic) pressure of wind, q = ½·ρ·v², from the wind speed and air density — the pressure the wind exerts when it is brought to rest against a surface — and also solves the wind speed back from a given pressure, reporting the speed in m/s, km/h and mph. The force endpoint computes the wind force on a surface, F = q·Cf·A, from the velocity pressure (or wind speed), the exposed area and a force coefficient (≈1.3 for a building wall, ≈1.2 for a flat plate), and — given a height — the overturning moment about the base. The beaufort endpoint converts between a wind speed and the Beaufort scale using v = 0.836·B^1.5, returning the Beaufort number, the standard description from calm to hurricane force and the corresponding pressure. Everything is computed locally and deterministically, so it is instant and private. Ideal for structural and façade-engineering tools, signage, solar-array, scaffold and temporary-structure wind checks, sailing and meteorology apps, and engineering education. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is structural wind pressure and force; for wind-turbine energy output use a wind-power API.

api.oanor.com/windload-api

Column Buckling API

Euler column buckling as an API, computed locally and deterministically. The critical-load endpoint computes the Euler critical (buckling) load of a slender column, Pcr = π²·E·I / (K·L)², from the Young's modulus, the second moment of area, the length and the end conditions — pinned-pinned (K=1), fixed-fixed (K=0.5), fixed-pinned (K≈0.7) or fixed-free / cantilever (K=2), or a custom effective-length factor — and, given the cross-section area, also the radius of gyration, slenderness ratio and critical buckling stress. The section endpoint returns the area, the second moment of area about both axes and the radius of gyration for a solid circle, a hollow circle or tube, or a rectangle, and highlights the weak-axis value that governs buckling. The slenderness endpoint computes the slenderness ratio λ = K·L/r and, given the modulus and yield strength, the transition slenderness λ1 = π·√(2E/σy) that separates long Euler columns from short and intermediate ones, classifies the column and returns both the Euler and the J.B. Johnson critical stresses. Everything is computed locally and deterministically, so it is instant and private. Ideal for structural, mechanical and aerospace engineering tools, strut and frame design, machine-design and stability-analysis apps, and engineering education. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is column buckling and stability; for beam bending, shear and deflection use a beam-statics API.

api.oanor.com/buckling-api

Mohr Circle Stress API

Mohr's circle and 2D (plane) stress transformation as an API, computed locally and deterministically. The principal endpoint takes a plane-stress state — the normal stresses σx and σy and the shear stress τxy — and returns the principal stresses σ1 and σ2 = (σx+σy)/2 ± √(((σx−σy)/2)² + τxy²), the maximum in-plane shear stress, the orientation of the principal and maximum-shear planes, the centre and radius of Mohr's circle, and the von Mises and Tresca equivalent stresses (treating plane stress with the third principal σ3 = 0). The transform endpoint rotates the stress state onto a plane at any angle θ, returning σx', σy' and τx'y' using the standard transformation equations, and confirms the σx+σy invariant. The safety endpoint computes the factor of safety against a material's yield strength under either the von Mises (distortion-energy) or the Tresca (maximum-shear) criterion, from a full stress state or from principal stresses directly. Everything is computed locally and deterministically, so it is instant and private. Ideal for mechanical, structural and aerospace engineering tools, finite-element pre- and post-processing, machine-design and stress-analysis apps, and engineering education. Pure local computation — no key, no third-party service, instant. Live, nothing stored. 3 endpoints. This is stress-state analysis; for fillet-weld throat sizing use a weld API and for helical-spring rates use a spring API.

api.oanor.com/mohr-api

Frequently asked questions

Quick answers about pricing, quotas, and integration.

How do I get an API key for Snow Load API?
Sign up for free at oanor.com, generate an API key from the developer dashboard, and call Snow Load API with the x-oanor-key header. No credit card needed for the free tier.
What's the rate limit for Snow Load API?
Free tier allows 1 request per second. Paid plans scale up to 50 requests per second on the Mega tier. Hard limits return HTTP 429 above the quota — no surprise overage charges.
How much does Snow Load API cost?
Snow Load API has a free tier with 100 calls / month. Paid plans start at €15.05 / month with higher quotas and faster rate limits.
Can I cancel my subscription anytime?
Yes. Plans are billed monthly and you can cancel anytime from your billing dashboard. No long-term contracts and no cancellation fee.
Is Snow Load API GDPR-compliant?
All requests to Snow Load API go through our EU-based gateway. Your upstream API key never leaves our server and no personal data is shared with the upstream provider beyond the request you send.

Pick an endpoint from the list on the left to see its details and try it.

Code snippets

Sign up to get an API key, then call any path under your slug.

curl https://api.oanor.com/snowload-api/SOME_PATH \
  -H "x-oanor-key: oanor_test_..."
const res = await fetch("https://api.oanor.com/snowload-api/SOME_PATH", {
  headers: { "x-oanor-key": "oanor_test_..." }
});
const data = await res.json();
$ch = curl_init("https://api.oanor.com/snowload-api/SOME_PATH");
curl_setopt($ch, CURLOPT_RETURNTRANSFER, true);
curl_setopt($ch, CURLOPT_HTTPHEADER, ["x-oanor-key: oanor_test_..."]);
$response = curl_exec($ch);
import requests
r = requests.get(
    "https://api.oanor.com/snowload-api/SOME_PATH",
    headers={"x-oanor-key": "oanor_test_..."},
)
print(r.json())

Ratings

Sign in to rate.

No reviews yet.

Discussion

Ask questions, share usage tips, get answers from the provider and other developers. Public — anyone can read.

Sign in to start a thread or reply.

Sign in

New thread

/ 4000

📌 Pinned 🔒 Locked

·

· ·

/ 4000

🔒 This thread is locked — no new replies.

  • No threads yet — start the discussion.

Support

Private 1:1 support with the provider — billing questions, integration issues, account problems. Only you and the provider team can see these threads.

Sign in to open a support ticket.

Sign in

Open new ticket

Describe what you need help with. The provider team gets an email and replies on the ticket page.

  • No tickets yet for this API.

Subscription active — calls can start immediately.

Send your first request —

Subscription active — copy a snippet and fire off your first call.